A. Individual Pilat (UW) Cascade Impactors
Item 3-1 Mark 3 Pilat (UW) Cascade Impactor (316 stainless steel). Includes single jet inlet stage section, 6 multi-jet stages, one set of 7 particle collection plates, outlet section with built-in filter (47 mm diameter filters) cylindrical casing, one set of lightweight stainless steel collection plate inserts (substrates), set of Viton o-rings, operations manual with graph of d50 versus the gas volumetric flow rate, and custom carrying case. Gas volumetric sampling flowrate at the Mark 3 Cascade Impactor temperature and pressure is in the 0.5 to 1.0 ft3/min. (or 14 to 28 liters/min.) range. Various substrates (stainless steel foil, glass fiber filter, ultrapure quartz microfiber, Teflon, etc.) can be used on the particle collection plates. Does not include sampling nozzles. -------- $5,800.00
Item 3-2 Mark 3 Particle Collection Plates. Extra Set of stainless steel (316 SS) particle collection plates comprised of one inlet plate (uses a 45 mm diameter particle collection substrate) and 6 multi-jet collection plates ("donut" shaped & use the donut shaped substrates). ---------- $950.00
Item 3-3 Mark 3 Foil Collection Plate Insert Substrates. Set of 7 lightweight stainless steel foil collection plate inserts, fit inside the particle collection plates (one 45 mm diameter disk for the #1 collection plate and 6 donut shaped foil inserts for collection plates #2-7). --------- $50.00
Item 3-4 Mark 3 to Mark 5 Conversion Kit. Consists of Mark 5 cylindrical casing, 7 Mark 5 multi-jet stages, 4 particle collection plates (donut shaped), jet stage spacer, one set of Mark 5 collection plate lightweight stainless steel inserts. -------- $5,150.00
Item 5-1 Mark 5 Pilat (UW) Cascade Impactor (316 SS). Includes single jet stage inlet section, 10 multi-jet stages, 11 particle collection plates, cylindrical casing, outlet section with built-in filter holder (47 mm diameter filters), two additional multi-jet stages (enables using various jet stages which allows sampling over a wider range of gas volumetric flow rates, from about 0.2 to 1.0 acfm), set of Viton O-rings, operations manual with graphs of jet stage cut diameter d50s versus the gas volumetric flow rate through the cascade impactor (at stack conditions), and custom carrying case. Gas volumetric sampling flowrate at the Mark 5 Cascade Impactor temperature and pressure is in the 0.2 to 1.0 ft3/min. (or 14 to 28 liters/min.) range. Note that the Mark 3 and Mark 5 Pilat Cascade Impactor parts are interchangeable. Does not include sampling nozzles. -------- $9,000.00
Item 5-2 Mark 5 Particle Collection Plates. Extra set of 316 stainless steel particle collection plates comprised of one inlet coll. plate (has 45 mm diameter disk shaped substrate) and 10 multi-jet collection plates ("donut" shaped which will use the donut shaped substrates). --------- $1,500.00
Item 5-3 Mark 5 Foil Collection Plate Insert Substrates. Extra set of 11 lightweight collection plate inserts (stainless steel foil) for the Mark 5 Pilat Cascade Impactor. -------- $ 60.00
Item 5-4 Mark 5 to Mark 3 conversion kit. Consists of Mark 3 cylindrical casing and #3 jet stages for the Mark 3 Pilat Cascade Impactor. -------- $900.00
Item 4-1 Mark 3 and 5 Sampling Nozzles. Set of six stainless steel standard "long" sampling nozzles which are threaded to screw into the Cascade Impactor inlet section with the first jet stage. Set of nozzles includes: 1/8", 3/16", 1/4", 5/16", 3/8", and 1/2" diameter inlets. --------- $1,050.00
C. Sampling Kits for Mark 3 and Mark 5 Pilat (UW) Cascade Impactors
PCSC recognizes that cascade impactor source sampling is greatly helped by having a number of cascade impactors because it reduces the turnaround time between tests and enables simultaneous testing with two or more sampling trains. Also, the variety of source testing situations (particle size distributions, particle mass concentrations, gas velocities, etc.) necessitate having some flexibility in choosing which cascade impactor (i.e. 7 jet stages in the Mark 3 casing, 11 jet stages in the Mark 5 casing, or 8-10 jet stages in the Mark 5 casing with the spacer used , etc.) to use. To meet these variable needs of the source tester, we have put together the sampling kits which contain 2 or more Pilat Cascade Impactors. These kits offer advantages with regards to price discounts compared to the individual cascade impactor prices. Note that the Mark 3 and Mark 5 Pilat (UW) Source Test Cascade Impactors have interchangeable parts (i.e. inlet sections, outlet sections, particle collection plates, impactor jet stages, substrates, etc. are all interchangeable) which helps improve the "user friendliness". The kits do not include the sampling nozzles because there are at least three different impactor inlet arrangements. The 3 inlet arrangements are: sampling nozzle connected to inlet section, Right Angle Inlet Section with two types of nozzles available (a longer nozzle and a shorter nozzle), and a Precutter with its special nozzles.
Item 1-1 CIS Kit (Complete Impactor Sampling Kit). Kit includes one Mark 5 Impactor (Item 5-1 @ $9,000) and one Mark 5 to 3 conversion kit (Item 5-4 @ $900) so that one can either sample with a Mark 3 or a Mark 5 impactor. Consists of Mark 5 Pilat (UW) Cascade Impactor complete with single jet inlet stage section, 10 multi-jet stages, one set of 11 particle collection plates, built-in backup filter (47 mm diameter) filter holder, outlet section, set of Viton o-rings, two additional jet stages, spacer, and operations manual with graphs of the cut diameter d50 versus gas volumetric flow rate; Mark 5 to 3 conversion kit consisting of Mark 3 cylindrical casing and a Mark number 7 jet stage; one box of #1 934AH 45 mm diameter glass fiber substrates (Item 7-1), 5 boxes of #2 (annular or "donut" substrates) 934AH glass fiber substrates (Item 7-2), one box of 934AH 47 mm diameter glass fiber backup filters (Item 7-3), 5 sets of lightweight stainless steel foil collection plate substrates for the Mark 5 (Item 5-3); and custom carrying case. Does not include sampling nozzles. ---------- $9,800.00
Item 1-2 SS 33 Kit (Simultaneous Sampling with two Mark 3 Pilat Cascade Impactors). Consists of two Mark 3 Pilat (UW) Cascade Impactors (Item 3-1 @ $5,800), each Mark 3 Pilat Cascade Impactors includes one single jet inlet stage section, 6 multi-jet stages, one set of 7 particle collection plates, cylindrical casing , outlet section with built-in filter (47 mm dia.) holder, set of Viton O-rings, one set of 7 lightweight stainless steel foil collection plate inserts, operations manual with graphs of particle cut diameter d50 versus gas flow rate, and custom carrying case. ------- $11,200.00
Item 1-3 SS 35 Kit (Simultaneous Sampling With Mark 3 and Mark
5 Pilat Cascade Impactors). Kit includes one Mark 3 Impactor (Item 3-1
@ $5,800) and one Mark 5 Impactor (Item 5-1 @ $9,000). Consists of one
Mark 3 Pilat (UW) Cascade Impactor which includes one single jet stage
inlet section, 6 multi-jet stages, one set of 7 particle collection plates,
a cylindrical casing, an outlet section with built-in filter holder (47
mm diameter filter), set of Viton O-rings, one set of 7 lightweight stainless
steel foil collection plate inserts, and operations manual with graphs
of particle cut diameter d50 versus gas
flow rate. Also consists of one Mark 5 Pilat (UW) Cascade Impactor complete
with single jet inlet section, 10 multi-jet stages, outlet section with
built-in filter holder, cylindrical casing, set of Viton O-rings, two additional
multi-jet stages, one set of 11 particle collection plates, one set of
11 lightweight stainless steel foil collection plate inserts, spacer, graphs
of particle cut diameter d50 versus gas
flow rate, and a custom carrying case. Does not include sampling nozzles.
----------- $14,500.00
Item 1-4 SS 55 Kit (Simultaneous Sampling with two Mark 5 impactors). Consists of 2 Mark 5 Pilat (UW) Cascade Impactors (Item 5-1 @ $9,000), each with a single jet inlet section, 10 multi-jet stages, an outlet section with built-in filter (47 mm dia. filters) holder, cylindrical casing, one set of 11 particle collection plates, one set of 11 lightweight stainless steel foil collection plate inserts (substrates), set of Viton O-rings, two additional multi-jet stages (enables wider range of gas volumetric sampling rates), jet stage spacer, operations manual with graphs of jet stage cut diameter d50 versus gas sampling volumetric flow rate, and custom carrying case. Does not include sampling nozzles. $17,500.00
Item 1-5 SS 88 Kit (Simultaneous Sampling with two Mark 3 and two Mark 5 Pilat Cascade Impactors). Kit consists of two Mark 3 Pilat (UW) Cascade Impactors and two Mark 5 Pilat (UW) Cascade Impactors. Essentially, this is two Item 1-4. ---------- $34,000.00
D. Accessories to Mark 3 and Mark 5 Pilat Cascade Impactors
Item 9-1 EPA Method 17 Thimble Filter Holder. Special inlet section to Mark 3 and Mark 5 cylindrical casing which will hold a 43 x 123 mm diameter thimble filter. The thimble filter fits onto a tapered inlet tube and a tapered retaining ring holds the filter in place. 316 SS. --------- $950.00
Item 12-1 PCSC Precutter. Consists of precutter body, end cap, outlet cap, tube connecting the precutter to the inlet section of the Mark 3 or Mark 5 Cascade Impactor. The PCSC Precutter aerodynamic cut diameter is related to the 0.5 inch diameter sampling nozzle single jet. --------- $2,000.00
Item 12-2 Precutter Nozzles. Set of 6 sampling nozzles for the PCSC Precutter and the Mark 8 High Grain Loading Impactor (1/8", 3/16", 1/4", 5/16", 3/8", 1/2"). 316SS. --------- $1,300.00
Item 13-1 Right Angle Sampling Attachment. The Right Angle Sampling attachment replaces the inlet section on the Mark 3 or 5 impactors and enables sampling at right angles to the axis of the impactor without using a "button hook nozzle". In other words, this Right Angle Sampling Attachment houses the #1 jet stage of the Mark 3 or 5 Cascade Impactors. Uses either the longer Item 4-1 sampling nozzles or the shorter Item 3-2 sampling nozzles. Consists of the Right Angle Sampling body, particle impaction collection plate pedestal (#1 lightweight foil substrate fits into this collection plate). ------- $1,900.00
Item 13-2 Nozzles for Right Angle Sampling Attachment. Set of 5 shorter sampling nozzles for the Right Angle Sampling Attachment. 316SS. (3/16", 1/4", 5/16", 3/8", 1/2"). Note that Item 4-1 "longer" sampling nozzles will also fit the Right Angle Sampling Attachment. --------- $ 1,150.00
E. Filter Substrates for Mark 3 and Mark 5 Pilat Cascade Impactors
Item 7-1 #1 collection plate 934 AH glass fiber substrate (45 mm diameter disk). 100 substrates per box.-- $90.00
Item 7-2 #2 collection plate 934 AH glass fiber substrate (donut). 100 substrates/box.- $100.00
Item 7-3 Box (100/box) of 47 mm diameter 934AH glass fiber filters for impactor outlet.--- $50.00
Item 7-4 #1 collection plate ultrapure quartz microfiber substrates (45 mm dia. disk). 100 substrates per box. $150.00
Item 7-5 #2 collection plate ultrapure quartz microfiber substrate (donut). 100/box ----- $275.00
Item 7-6 Box (100/box) of 47 mm diameter ultrapure quartz microfiber
outlet filters ----- $100.00
Note: The filter substrates of Items 7-1, 7-2, 7-4, & 7-5 should be held in place with the lightweight stainless steel foil collection plate inserts (Items 3-3 or 3-5). These stainless steel foil collection plates protect the fiberglass substrates and are commonly weighed together with the fiberglass substrate (i.e. weigh the stainless steel foil insert and the fiberglass substrate as one substrate).
F. Mark 8 High Grain Loading Cascade Impactor
This 3 stage cascade impactor is designed to collect larger amounts (grams) of particles such as might occur during the sampling of high (greater than 0.1 grains/acf) particle concentrations. This impactor can be used to collect larger amounts (grams) of particles which might be needed for later chemical analysis.
Item 8-1 The Mark 8 Impactor includes a special precutter inlet stage (single jet through the sampling nozzle), a stage 2 chamber, stage 3 chamber, and outlet section with thimble filter. This Mark 8 high Grain Loading Cascade Impactor divides the particles into 4 particle samples which are fractionated by particle diameter (cut diameters of 10.8, 5.8, and 1.5 microns at a gas sampling rate of 0.5 acfm at 70oF). Included are six sampling nozzles of 1/8", 3/16", 1/4", 5/16", 3/8", 1/2" diameters (same as Precutter nozzles). --------- $9,800.00
Price List (Effective March 26, 2002)
To place a purchase order, FAX it to (206) 523-7221.
Delivery is typically one week from order receipt. Most items are in
stock and should be able to be shipped within 4-7 days of the receipt of
the purchase order. Our prices are usually updated once per year. However,
prices are subject to change without notice.
8. Fees: All banking charges to the account of the buyer
including all amendments, confirmation, acceptance, and discount fees.
9. Presentation: Allow 15 days, after the required shipment
date, for presentation of the documents.
10. The Letter of Credit is to be payable against the presentation
of the following documents: Draft drawn on the Bank of America ,
Commercial Invoice, and Airway Bill.
Note: All documents to be consigned to the
Bank and notify the applicant (buyer). All copies and originals of
the Airway bill will be sent to the Bank only. All shipping documents
shall show USA as the origin.
11. Freight Forwarder: Pollution Control Systems Corp.
will use the forwarder of our choice.
The Letter of Credit must be acceptable to Pollution Control Systems
Corp. and our Bankers (Bank of America) before our obligations to the buyer
(applicant) may be considered final.